RollenceLogo

Hi there ๐Ÿ‘‹

Need help? Search our help center for answers or start a conversation:

Help Center

New Conversation

We typically reply in a few minutes

Support Customer Support
Customer Support
Support
Welcome to our site, if you need help simply reply to this message, we are online and ready to help.
Support

Select Emoji

Rollence Granito GHR + Punch finish tiles made in Morbi, Gujarat
Made in Morbi, Gujarat

Anti Skid Tiles (GHR + Punch): The Grip Finish for Bathrooms and Balconies

GHR + Punch finish GVT and PGVT Group BIa
8 Finishes in the range
6 Collections
0.5% Water absorption or less
BIa ISO 13006 class

No products found.

โ† View all products
Overview

GHR + Punch Tiles at Rollence

Anti skid tiles have a textured surface that grips a wet shoe or a bare foot, and in the Rollence list that job belongs to GHR + Punch. GHR stands for Glazed High Relief, a floor surface with a raised texture over the glaze, and the punch pattern is pressed into it. Rollence makes GHR + Punch in GVT for floors and walls and in PGVT for walls, at its factory in Matel, Wankaner, Morbi, Gujarat, as part of its porcelain tile range.

GHR + Punch is one of eight Rollence finishes, and it is the one to look at first for any floor that gets wet, since anti skid tiles matter most where water meets feet. Bathrooms, balconies, terraces and entrance porches are the main places, and the design list on the site can be filtered by finish to show which patterns carry it. Every tile absorbs 0.5% water or less, so the body does not soak up rain.

In the Morbi market, anti skid GVT sells at about Rs. 60 to Rs. 140 per sq.ft and PGVT at Rs. 70 to Rs. 180 per sq.ft, so one 600x600 mm (2x2 ft) GVT tile costs about Rs. 230 to Rs. 540. These are market reference ranges and not a Rollence quote. Textured tiles can take longer to lay and clean, so budget Rs. 15 to Rs. 60 per sq.ft for labour.

The Finish

Anti Skid Tiles: What GHR + Punch Gives You

Grip comes from the surface, not the body. A high relief glaze stands up in small peaks, and water runs into the gaps between them, so the sole of a shoe meets the peaks and not a film of water. The punch pattern adds a second texture on top, which is why the surface looks more like rough stone than a smooth floor.

The body beneath is the same dense GVT as every other finish, with water absorption of 0.5% or less, and Rollence batches are tested to the ISO 10545 series. The quality testing record is the place to check how each batch is measured.

Versus Carving

GHR + Punch vs DG Matt + Carving: Two Textured Finishes

The nearest finish in the list is carving tiles, and the two are often confused. Carving is a matt tile with a carved relief, chosen mainly for how a wall looks. GHR + Punch is a floor surface chosen mainly for how it grips, and its texture is rougher and more pronounced.

Point GHR + Punch DG Matt + Carving
Main purpose Grip on wet floors Depth on walls and dry floors
Texture Rougher, higher relief Carved, softer relief
Bathroom floor Yes, once the design is rated R10 or R11 Only if the design is rated R10 or R11
Wipe-clean Needs a brush Needs a brush

A texture that grips well also holds more dirt. Both finishes need a stiff nylon brush, and neither is the right pick for a room where a smooth, wipe-clean floor matters more than grip.

Bathrooms

Anti Skid Tiles for Bathroom Floors

Anti skid tiles for bathroom floors are the most searched use of the finish, because a wet marble-look floor is the most common cause of a fall at home. A small tile follows the floor slope to the drain better than a large one, and 600x600 mm tiles of 3.9 sq.ft need 278 pieces per 100 mยฒ. More joints also means more grip underfoot.

Note

Glossy and High Gloss finishes should not be used on bathroom floors because they turn slippery when wet. PGVT should not be used on any floor, as it is a wall tile.

Fill every joint with epoxy grout. Cement grout in a bathroom absorbs soap and water, goes dark and grows mildew in a humid Gujarat monsoon, while epoxy grout stays sealed and keeps its colour.

Outdoors

Non Slip Outdoor Tiles for Balconies and Terraces

Non slip outdoor tiles take a month of monsoon rain, then summer heat on the same surface. The Rollence site is clear that polished and high gloss surfaces are not suitable for terraces, pool surrounds or external paving, and it recommends a matt or textured finish with an R10 or R11 rating. Stone and concrete effects hide dirt well outside, and the Stonique collection is a natural place to look.

Slope the floor slightly towards a drain, so water leaves and does not sit. Use epoxy grout, leave expansion joints at the edges, and keep spare tiles from the same batch.

Slip Ratings

Reading Slip Ratings Before You Buy

The usual test is DIN 51130, a ramp test that grades floors from R9 to R13, and a higher number means more grip. The Rollence site advises R10 or R11 for wet and external floors. Ask for the figure of the exact design, because two designs in the same finish can rate differently, and keep the rating in writing with the test certificates.

Do not rely on how rough a sample feels. A tile can feel gritty in the hand and still give poor grip when wet, while a finer relief can rate higher. The rating is the only reliable answer.

Care

Laying and Cleaning Textured Floors

Use full-coverage adhesive and a notched trowel, and press each tile down with a rubber mallet. Wipe adhesive off the surface at once, because it sets in the grooves and is hard to remove. Order 10% extra for cuts.

For cleaning, sweep first, then scrub with a stiff nylon brush and a neutral cleaner, and rinse well. The care and maintenance routine for textured floors is a weekly brush and a monthly deeper clean. Avoid acid cleaners, which attack grout.

Plan Your Order

Plan Your Order

A grip surface should be seen and touched before it goes on a floor, because the same finish can look quite different under a bathroom light. Free samples reach the door from Rollence Granito, and the quote follows the size, collection, quantity and city you name in the enquiry form.

Request Samples
Quick Facts

Quick Facts on Anti Skid Tiles from Morbi

What do anti skid tiles cost in Morbi?

A 600x600 mm (2x2 ft) anti skid GVT tile from the Morbi market costs about Rs. 60 to Rs. 140 per sq.ft, roughly Rs. 230 to Rs. 540 per tile, and 278 tiles cover 100 m². The body absorbs 0.5% water or less. PGVT costs Rs. 70 to Rs. 180 per sq.ft and is for walls only. These are market ranges, not a Rollence quote.

Do anti skid tiles work in a Gujarat monsoon?

Anti skid tiles work in a Gujarat monsoon when the design is rated R10 or R11 and the body absorbs 0.5% water or less, the BIa limit under IS 15622. A 600x1200 mm (2x4 ft) tile suits a larger balcony. Morbi factories make GVT at Rs. 60 to Rs. 140 per sq.ft, and epoxy grout keeps the joints sealed.

FAQ

Questions About GHR + Punch Tiles

What does GHR mean on a tile?

GHR means Glazed High Relief, a floor surface with a raised texture over the glaze that gives grip. Rollence lists it as GHR + Punch, in GVT for floors and walls and in PGVT for walls only. Always ask for the slip rating of the exact design before laying it.

Which anti skid tiles are best for bathroom floors?

Choose a textured GVT tile rated R10 or R11 under DIN 51130, in a smaller size such as 600x600 mm. Small tiles follow the drain slope and add joints for grip. Use epoxy grout throughout. Glossy tiles and PGVT should never be used on bathroom floors.

Can anti skid tiles be used outdoors?

Yes, anti skid tiles suit balconies, terraces and entrance porches when the design is rated R10 or R11. A textured GVT body absorbs 0.5% water or less, so monsoon rain does not soak in. Avoid glossy and high gloss finishes outdoors, as they turn slippery when wet.

What does R10 or R11 mean on a tile?

R10 and R11 are slip grades from the DIN 51130 ramp test. The scale runs from R9 to R13, and a higher number means more grip. The Rollence site advises R10 or R11 for wet and external floors. Ask for the grade of the exact design in writing.

Are anti skid tiles hard to clean?

They need more effort than a flat tile because dirt settles in the texture. Sweep first, then scrub with a stiff nylon brush and a neutral cleaner, and rinse with clean water. Epoxy grout stays cleaner than cement grout, and acid cleaners should be avoided.

What is the price of anti skid tiles per sq.ft?

Anti skid GVT costs about Rs. 60 to Rs. 140 per sq.ft in the Morbi market. PGVT costs Rs. 70 to Rs. 180 per sq.ft but is for walls only. Laying labour adds Rs. 15 to Rs. 60 per sq.ft. Prices change with design, size and city, and they are not a Rollence quote.

Can I use PGVT as an anti skid floor tile?

No, PGVT is a polished wall tile and must not be laid on any floor, wet or dry. The polished surface is slippery and shows scuffs. For grip, use GVT in a textured finish with an R10 or R11 rating, and keep PGVT for walls.

Keep Exploring

Related Rollence Pages