Hi there ๐
Need help? Search our help center for answers or start a conversation:
Help Center
New Conversation
We typically reply in a few minutes
Select Emoji
Quick Enquiry
We'll get back to you within 24 hours
1200x1200 mm tiles are the square large format, 4x4 ft each, and one of the three sizes Rollence features first. They suit lobbies, showrooms and big living halls where a square grid looks deliberate and the floor needs very few joints. The 1200x1200 mm tile belongs to the same factory range as Rollence's porcelain tiles at Matel, Wankaner, Morbi, Gujarat, though it is sold as large format GVT for floors and walls and as large format PGVT for walls.
One 1200x1200 mm tile covers 1.44 mยฒ (15.5 sq.ft), so 100 mยฒ needs 70 tiles and the grout run is about 167 m. Rollence makes eight finishes in six collections, and the design list on the site can be filtered by size to show what is made in 1200x1200 mm. The body of each tile absorbs 0.5% water or less.
In the Morbi market, GVT in this size sits in the upper half of the Rs. 60 to Rs. 140 per sq.ft range, and PGVT in the upper half of Rs. 70 to Rs. 180, which puts one GVT tile at roughly Rs. 930 to Rs. 2,200. These are market reference ranges and not a Rollence quote. Buyers across Gujarat and India search for the size as 4x4 tiles.
1200x1200 mm tiles are best for large rooms where a square grid is part of the design: lobbies, showrooms, banquet halls, big living halls and open offices. The square shape has no direction, so it does not point the eye toward one wall, and the large size keeps joints to a minimum. A room needs to be at least 4.8 m wide to show four whole tiles across.
A 6 m by 8 m lobby is 48 mยฒ, which needs 34 tiles before wastage and 37 with 10% added. A tile calculator does the same arithmetic for any room. Compare that with 134 tiles for the same lobby in 600x600 mm, and the saving in laying time and grout is clear.
Replacement cost rises with size. One 1200x1200 mm tile of 15.5 sq.ft costs roughly Rs. 930 to Rs. 2,200 at GVT market rates, so order two spare tiles from the same batch for any project over 50 mยฒ.
Compared with 800x3000 mm tiles, which share a similar grout run of 158 m per 100 mยฒ, the square 1200x1200 mm tile is far easier to carry, cut and fit around columns. A 3 m tile is a wall product, and a 1.2 m square is a floor product, so the two rarely compete for the same job.
| Size (mm) | Alias (ft) | Tiles per 100 m² | Grout run per 100 m² | Typical use |
|---|---|---|---|---|
| 1200x1200 This size | 4x4 | 70 | About 167 m | Lobbies, showrooms |
| 800x800 | 2.6x2.6 | 157 | About 250 m | Open living and dining |
| 800x1600 | 2.6x5.2 | 79 | About 188 m | Large living areas, walls |
| 1200x1800 | 4x6 | 47 | About 139 m | Showrooms, large halls |
| 1200x2400 | 4x8 | 35 | About 125 m | Commercial lobbies, wall spans |
Against 800x800 mm, the grout run falls from 250 m to 167 m, and the tile count falls from 157 to 70. Against 1200x1800 mm, 1200x1200 mm has the same width but a shorter length, which makes it lighter to lift and easier to align on a floor that is not perfectly flat.
Rollence makes 1200x1200 mm in large format GVT and large format PGVT. GVT carries a digital print under a hard glaze and goes on floors and walls, so it is the category for lobbies, showrooms and halls. PGVT has a polished surface and is made for walls only, which suits a reception wall or lift cladding.
| Category | Surface | Where it goes | Water absorption |
|---|---|---|---|
| Large format GVT | Digital print under a hard glaze | Floors and walls | 0.5% or less |
| Large format PGVT | Polished glaze surface | Walls only | 0.5% or less |
PGVT should not be used on floors, wet or dry, because the polished surface turns slippery when wet and shows scuffs under foot traffic.
Rollence is ISO 9001:2015 certified, and every batch goes through ISO 10545 testing before dispatch. For a showroom or banquet hall, a client or consultant may ask for the water absorption result, and a figure of 0.5% or less is the number to quote.
Rollence lists eight finishes, and the design list on the site shows which are made in 1200x1200 mm. The table sets out where the main four belong for a 4x4 ft tile.
| Finish | Best placed | Keep away from |
|---|---|---|
| DG Matt | Halls, living rooms, offices, corridors | Wet or outdoor floors unless rated R10 or R11 |
| Glossy | Dry showrooms and lobbies | Bathroom floors, balconies |
| High Gloss | Dry reception areas and feature walls | Bathroom floors, balconies, outdoors |
| GHR + Punch | Wet areas, semi-covered floors | Rooms that need a smooth, wipe-clean surface |
Most homes laying 1200x1200 mm tiles choose matt finish tiles, because a large glossy square shows every footprint and cleaning streak. A matt surface also hides small differences in tile level, which matters on a big floor.
Glossy and High Gloss finishes should not be used on outdoor or wet floors because they turn slippery when wet.
Entrance lobbies in Gujarat get wet footprints through the monsoon. Use matt or textured GVT near the door, rated R10 or R11 under DIN 51130, and seal the joints with epoxy grout so that water does not stain the grid.
Showrooms, banquet halls and mall corridors are the natural homes of 1200x1200 mm tiles, because a big square grid looks organised under bright lights and needs little grout maintenance. Corporate lobbies use the same size for the same reasons.
In homes, the size suits a large living hall of 30 mยฒ or more. Marbella is the marble look tiles collection for buyers who want veined squares, and the finish and body should match the surface: GVT underfoot, PGVT on the wall.
Avoid 1200x1200 mm in small rooms, narrow passages and wet bathrooms, where cutting waste is high and a drain slope cannot be followed. Use 600x600 mm there instead.
Check the base with a 2 m straightedge before laying, and level any high spot. Use full-coverage adhesive with back-buttering, and levelling clips on every joint, because a square large tile shows lippage at the corners. A square tile does not bow along a long edge, so a straight grid is easy to keep aligned.
Two workers should carry each tile on its edge, with suction cups for placement. A 1.2 m tile fits through standard doors and most staircases on edge, which longer formats cannot. The adhesive and levelling method used for large format tiles applies to every size from 800x1600 mm upward.
Order 10% extra for a straight layout and 15% for diagonal laying. Cut with a wet saw or a bridge saw and wipe grout haze within a day. Allow movement joints at doorways and at regular intervals in large halls.
A 1200x1200 mm square is a big commitment for a lobby, so view a real piece beside your wall colour and lighting before fixing the quantity. Rollence Granito sends samples free of charge to your door, and quotations follow from size, finish, collection, quantity and destination city. Submit those five details with the enquiry form.
A 1200x1200 mm GVT tile (4x4 ft) from Morbi sits in the upper half of the Rs. 60 to Rs. 140 per sq.ft market range, which is roughly Rs. 930 to Rs. 2,200 per tile, and 70 tiles cover 100 m². The body absorbs 0.5% water or less. PGVT in this size costs about Rs. 1,100 to Rs. 2,800 per tile for walls only, at Rs. 70 to Rs. 180 per sq.ft.
Epoxy grout suits a 1200x1200 mm (4x4 ft) floor in Gujarat's humid monsoon, because it does not absorb water or stain from wet footprints. The tile body from Morbi absorbs 0.5% water or less, the BIa limit under IS 15622, and 77 tiles including wastage cover 100 m² at Rs. 60 to Rs. 140 per sq.ft.
A 4x4 ft tile is about 1200x1200 mm, or 120x120 cm. It covers 1.44 m², which is 15.5 sq.ft. Rollence makes this size as large format GVT for floors and walls and as large format PGVT for walls only, and features it among its main sizes.
You need 70 tiles of 1200x1200 mm for 100 m², and about 77 with 10% wastage. Each tile covers 1.44 m², so 100 divided by 1.44 gives 69.4, rounded up. The grout run on that floor is about 167 m.
GVT in 1200x1200 mm costs Rs. 60 to Rs. 140 per sq.ft in the Morbi market, toward the upper half. PGVT costs Rs. 70 to Rs. 180, also toward the upper half. One tile of 15.5 sq.ft costs roughly Rs. 930 to Rs. 2,200. These are market ranges and not a Rollence quotation.
Yes, in a large living hall of 30 m² or more with a flat base. In small rooms it wastes tile on cuts. Choose matt GVT, full-coverage adhesive and epoxy grout, and keep two spare tiles from the same batch, since one tile is a costly repair.
No, PGVT is a polished wall tile and should not be laid on any floor, wet or dry. The polished surface turns slippery when wet and shows scuffs under foot traffic. Use GVT for floors, and keep PGVT 1200x1200 mm for feature walls and cladding.
A room should be at least 4.8 m wide to show four whole tiles across, and 3.6 m for three. Narrower rooms leave thin cut strips at the walls. Plan the layout from the centre of the room, so that cuts at both walls are equal and at least half a tile.
Yes, levelling clips are recommended on every joint for 1200x1200 mm tiles, because a large square tile shows lippage at its corners. Combine them with full-coverage adhesive and back-buttering. Remove the clips after the adhesive has cured, and wipe the joint before grouting.
Product Inquiry
Fill in your details and we'll get back to you